Hello,
I also bought such a module and was able to successfully flash it with Annex version 151.3. The display works excellently with the configuration posted by Botman. My question is whether it is possible to integrate the touch and SD card functionality into Annex. Since that If the module is available for 10-15 euros, it would be an inexpensive way to operate a complete system with a display, SD card, sound amplifier, LDR, RGB LED with annex
Greetings Monki
ILI9341 not full screen
-
- Posts: 345
- Joined: Tue Jun 21, 2022 2:17 pm
- Location: South coast UK
- Has thanked: 183 times
- Been thanked: 112 times
Re: ILI9341 not full screen
That's great news. Keep us posted. It's a nice and cheap module and if you are succesfull with some simple mods it could really help others.
-
- Posts: 99
- Joined: Fri Dec 09, 2022 10:03 am
- Has thanked: 42 times
- Been thanked: 9 times
Re: ILI9341 not full screen
i have a ESP§"-2432S028 and i use it with this parameter:
ILI9341 CUSTOM
Mosi 13
Miso 12
Sclk 14
CS 15
DC 2
BL 21
ILI9341 CUSTOM
Mosi 13
Miso 12
Sclk 14
CS 15
DC 2
BL 21
You do not have the required permissions to view the files attached to this post.
-
- Posts: 42
- Joined: Mon Feb 27, 2023 12:56 pm
- Location: Berlin
- Has thanked: 6 times
- Been thanked: 6 times
Re: ILI9341 not full screen
Hello Helmut,
This corresponds exactly to my configuration. The LDR can be queried with ambient light = ADC (34). However, the voltage divider ratio for the LDR is poorly chosen, so that when the LDR is completely covered, only about 40mV can be measured at PIN 34 and 0mV when there is light .
This means that the digital values are only in the lower range (0-190 of the AD converter.
It would be nice if cicciocb could integrate the SD card and the TOUCH as a software solution.
Monki
This corresponds exactly to my configuration. The LDR can be queried with ambient light = ADC (34). However, the voltage divider ratio for the LDR is poorly chosen, so that when the LDR is completely covered, only about 40mV can be measured at PIN 34 and 0mV when there is light .
This means that the digital values are only in the lower range (0-190 of the AD converter.
It would be nice if cicciocb could integrate the SD card and the TOUCH as a software solution.
Monki
- cicciocb
- Site Admin
- Posts: 2060
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1358 times
- Contact:
Re: ILI9341 not full screen
Do not hesitate to give a donation so that I can buy the module and implement the support
-
- Posts: 42
- Joined: Mon Feb 27, 2023 12:56 pm
- Location: Berlin
- Has thanked: 6 times
- Been thanked: 6 times
Re: ILI9341 not full screen
Hello Francesco,
I just donated, hope you give us a little Christmas present
I just donated, hope you give us a little Christmas present
- cicciocb
- Site Admin
- Posts: 2060
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1358 times
- Contact:
Re: ILI9341 not full screen
I just now sent another small donation toward CYD module support with Annex32.
- cicciocb
- Site Admin
- Posts: 2060
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1358 times
- Contact:
Re: ILI9341 not full screen
Thanks, I hope It will be possible to implement the support for the SD, the touch and the TFT at the same time.
Re: ILI9341 not full screen
The CN1 connector is easily usable as an I2C port.
My son connected a WII Nunchuk and installed a non-Annex program to play video games on this module.
I played Pac-man with good graphics and sound on it yesterday.
My son connected a WII Nunchuk and installed a non-Annex program to play video games on this module.
I played Pac-man with good graphics and sound on it yesterday.