Have you set the TFT display in the config?[Local Link Removed for Guests] wrote: [Local Link Removed for Guests]Thu Oct 19, 2023 7:33 pm I can't use the code, in Annex32 CAN 1.50.8 LFS and in newer Firmware, TFT Int, TFT.TJPG and so on.
Round display GC9A01
- cicciocb
- Site Admin
- Posts: 2095
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 450 times
- Been thanked: 1385 times
- Contact:
Re: Round display GC9A01
You do not have the required permissions to view the files attached to this post.
-
- Posts: 108
- Joined: Fri Dec 09, 2022 10:03 am
- Has thanked: 47 times
- Been thanked: 12 times
Re: Round display GC9A01
I think so,
by the way, can you insert Modbus TCP insert the ESP Basic?
by the way, can you insert Modbus TCP insert the ESP Basic?
You do not have the required permissions to view the files attached to this post.
-
- Posts: 108
- Joined: Fri Dec 09, 2022 10:03 am
- Has thanked: 47 times
- Been thanked: 12 times
Re: Round display GC9A01
Hmm,
gestern Abend, nach den Fehlermeldungen, aufgehört......
Jetzt gerade mal wieder eingesteckt und ....... es gab eine Fehlermeldung Syntax error und beim nächsten save und run läuft es.
Ich werde mir merken, dass ein abstecken eventuell mal hilft.
Hmm,
Stopped yesterday evening after the error messages...
Now I just plugged it back in and ....... there was an error message Syntax error and the next time I save and run it works.
I'll remember that unplugging might help.
gestern Abend, nach den Fehlermeldungen, aufgehört......
Jetzt gerade mal wieder eingesteckt und ....... es gab eine Fehlermeldung Syntax error und beim nächsten save und run läuft es.
Ich werde mir merken, dass ein abstecken eventuell mal hilft.
Hmm,
Stopped yesterday evening after the error messages...
Now I just plugged it back in and ....... there was an error message Syntax error and the next time I save and run it works.
I'll remember that unplugging might help.
-
- Posts: 108
- Joined: Fri Dec 09, 2022 10:03 am
- Has thanked: 47 times
- Been thanked: 12 times
Re: Round display GC9A01
zu früh gefreut
Error there again
Error there again
You do not have the required permissions to view the files attached to this post.
- cicciocb
- Site Admin
- Posts: 2095
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 450 times
- Been thanked: 1385 times
- Contact:
Re: Round display GC9A01
It seems that you have tft.init.0 and tft.init.0 that are not correct.[Local Link Removed for Guests] wrote: [Local Link Removed for Guests]Fri Oct 20, 2023 8:42 pm zu früh gefreut
Error there again
You must remove the .
-
- Posts: 108
- Joined: Fri Dec 09, 2022 10:03 am
- Has thanked: 47 times
- Been thanked: 12 times
Re: Round display GC9A01
Es muss was mit dem Speicher zutun haben, denn ganz kurz erscheinen im Display Daten von Versuchen davor.
Ist es ev im Cache im Rechner, oder eher im ESP32?
It must have something to do with the memory, because data from previous attempts appears very briefly in the display.
Is it perhaps in the cache on the computer, or rather in the ESP32?
Ist es ev im Cache im Rechner, oder eher im ESP32?
It must have something to do with the memory, because data from previous attempts appears very briefly in the display.
Is it perhaps in the cache on the computer, or rather in the ESP32?
- cicciocb
- Site Admin
- Posts: 2095
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 450 times
- Been thanked: 1385 times
- Contact:
Re: Round display GC9A01
the lines 7 and 8 of your program are not correct
must be
line 7 : TFT.INIT 0
line 8 : TFT.FILL 0
must be
line 7 : TFT.INIT 0
line 8 : TFT.FILL 0
-
- Posts: 108
- Joined: Fri Dec 09, 2022 10:03 am
- Has thanked: 47 times
- Been thanked: 12 times
Re: Round display GC9A01
Yes, i found it out, but the syntax error is by tft.jpg "/mosca.jpg" , too
And i think it is right?
And by : tft.image "/Jo_van_Gogh.jpg" and by tft.jpg "/casio.jpg", then by gui.init 2 : syntax error too
And i think it is right?
And by : tft.image "/Jo_van_Gogh.jpg" and by tft.jpg "/casio.jpg", then by gui.init 2 : syntax error too
Last edited by Helmut_number_one on Sat Oct 21, 2023 7:54 am, edited 1 time in total.
- cicciocb
- Site Admin
- Posts: 2095
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 450 times
- Been thanked: 1385 times
- Contact:
Re: Round display GC9A01
Yes the command is correct.
Maybe you have some wrong hidden characters on the line
try to delete that line and write again (no copy paste) or try to replace tft.jpg with TFT.IMAGE
Maybe you have some wrong hidden characters on the line
try to delete that line and write again (no copy paste) or try to replace tft.jpg with TFT.IMAGE
- cicciocb
- Site Admin
- Posts: 2095
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 450 times
- Been thanked: 1385 times
- Contact:
Re: Round display GC9A01
All the commands works well for me, check the syntax of your program.
When yo have an error, delete the line and write by hand again, maybe you did a bad copy/paste from another source
When yo have an error, delete the line and write by hand again, maybe you did a bad copy/paste from another source