Page 2 of 2
Re: Base64 encoder
Posted: Mon Aug 28, 2023 6:59 pm
by cicciocb
I just uploaded the ESPCAM 1.51.1.
You can use the OTA or the online flasher to update.
I did not tested so, let me know.
Re: Base64 encoder
Posted: Tue Aug 29, 2023 10:15 am
by rmsta
I tried to test this morning, but honestly, perhaps I made a mistake when flashing a module where a Ver 1.49.2 CAM was running stable before:
Connected the module to the WEB Installer (this was the mistake) and flashed 1.51.1 ESP32 to the module. Annex worked so far. When I noticed the error, I flashed 1.51.1 CAM via OTA, which also worked. But since then the camera couldn´t be adressed in any way. Finally I erased the flash via the Toolkit and flashed 1.49.2 CAM and later 1.48.22 CAM also via the toolkit, the result is in all cases the same:
When adressing the camera eg
Code: [Local Link Removed for Guests]
'
'Ver 1.48.22
wlog "init"
Ret = CAMERA.PARAMS("framesize",13)
wlog Ret
wait
This ended with reboot:
Code: [Local Link Removed for Guests]
Number of program lines :6
Basic File Loaded: /test.bas
Program RunningProgram Running
Guru Meditation Error: Core 1 panic'ed (LoadProhibited). Exception was unhandled.
Core 1 register dump:
PC : 0x400e57e8 PS : 0x00060830 A0 : 0x800e4ad7 A1 : 0x3ffcdd60
A2 : 0x00000000 A3 : 0x3ffd6ac4 A4 : 0x3ffc5cac A5 : 0x3f41b508
A6 : 0x3ffcddbc A7 : 0x0000000d A8 : 0x800e57e4 A9 : 0x3ffcdd40
A10 : 0x00000001 A11 : 0x0000000d A12 : 0x3ffd635c A13 : 0x3ffc3df4
A14 : 0x00000008 A15 : 0x7ffa0000 SAR : 0x00000014 EXCCAUSE: 0x0000001c
EXCVADDR: 0x00000040 LBEG : 0x4008ca6d LEND : 0x4008ca91 LCOUNT : 0x8011870a
Backtrace: 0x400e57e5:0x3ffcdd60 0x400e4ad4:0x3ffcddf0 0x400e4c13:0x3ffcde30 0x400e4e78:0x3ffcde60 0x400e7cce:0x3ffcde90 0x4008210e:0x3ffcdec0 0x400f063f:0x3ffcdef0 0x400f088c:0x3ffcdf50 0x40117855:0x3ffcdf90
ELF file SHA256: 0000000000000000
Rebooting...
ets Jun 8 2016 00:22:57
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1344
load:0x40078000,len:13864
load:0x40080400,len:3608
entry 0x400805f0
Annex initializing...
PSRAM enabled
module Type 0 Display 255 SD_Card 0
OK
No SD cards found. Reverts to FFAT
AnnexCAM 1.48.22
(C) ciccioCB 2022
Personal use only, commercial use strictly prohibited
Chip revision 1 Freq 240
STARTING
Connecting to abc
.............
Connected to abc
IP address: 192.168.0.59
ws[/ws][1][2] connect
I feel for the next tests, I have to buy a new module.
Any other idea would be appreciated very much.
Rainer
Re: Base64 encoder
Posted: Tue Aug 29, 2023 1:53 pm
by cicciocb
I tested personally yesterday night and it was working.
I think that you didn't selected the right module in the config page so the camera is not initialized.
This message is not correct
Code: [Local Link Removed for Guests]
module Type 0 Display 255 SD_Card 0
The module type should be 201 (for the esp32-cam or 202 for the M5 camera)
Re: Base64 encoder
Posted: Tue Aug 29, 2023 3:56 pm
by rmsta
Ooh, you are right ! I was too fast and forgot to set the module type on then config page.
Meanwhile I flashed another 2 "garden" CAMs and I can confirm everything is working as expected.
I thint the picture buffer works as in 1.48.22, but taking 4 additional pictures doesn´t matter.
Thank you for the hint !
Rainer