New AnnexToolKit 1.1 including release 1.48.22
- cicciocb
- Site Admin
- Posts: 2060
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1358 times
- Contact:
Re: New AnnexToolKit 1.1 including release 1.48.22
Have you tried the USB version?
I think that you loaded the Full version that use the serial port.
edit:
Sorry, It looks that the module you bought is equipped with a USB to serial chip.
I think that you loaded the Full version that use the serial port.
edit:
Sorry, It looks that the module you bought is equipped with a USB to serial chip.
- cicciocb
- Site Admin
- Posts: 2060
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1358 times
- Contact:
Re: New AnnexToolKit 1.1 including release 1.48.22
I just received today the same module as you but without the USB to Serial chip
This is what I have with the default firmware installed
and I confirm that I have the same problem as you :
This is a good news as I can understand why this happens
This is what I have with the default firmware installed
Code: [Local Link Removed for Guests]
I/main LuatOS@ESP32C3 base 22.10 bsp V1001
ESP-ROM:esp32c3-api1-20210207
Build:Feb 7 2021
rst:0x15 (USB_UART_CHIP_RESET),boot:0xc (SPI_FAST_FLASH_BOOT)
Saved PC:0x40387546
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fcd5820,len:0x10c4
load:0x403cc710,len:0x738
load:0x403ce710,len:0x2aa4
entry 0x403cc710
I/main LuatOS@ESP32C3 base 22.10 bsp V1001
I/main ROM Build: Oct 10 2022 22:06:59
D/main loadlibs luavm 98296 9960 9960
D/main loadlibs sys 181040 39444 43272
D/wlan esp_wifi_init ret 0
D/wlan wifi event 2
D/wlan esp_wifi_start ret 0
D/wlan wifi station start
D/wlan softap luatos 12341234
D/wlan wifi event 3
D/wlan esp_wifi_stop ret 0
I/wlan auto set to APSTA mode
D/wlan esp_wifi_set_mode ret 0
D/wlan esp_wifi_set_config ret 0
D/wlan wifi event 2
D/wlan wifi event 12
D/wlan esp_wifi_start ret 0
D/wlan apstart ret 0
D/wlan wifi station stop
D/wlan wifi station start
D/wlan wifi ap start
D/httpsrv http accept wait
I/httpsrv http listen at 0.0.0.0:80
I/user.web pls open url http://192.168.4.1/
Code: [Local Link Removed for Guests]
ESP-ROM:esp32c3-api1-20210207
Build:Feb 7 2021
rst:0x3 (RTC_SW_SYS_RST),boot:0xc (SPI_FAST_FLASH_BOOT)
Saved PC:0x40383a6e
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fcd6100,len:0x438
load:0x403ce000,len:0x918
load:0x403d0000,len:0x24e4
SHA-256 comparison failed:
Calculated: 080c5cb68a075ced55f248b97bca965e3e5bd5da80a64e34e6a1638f89d6f64e
Expected: ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff
Attempting to boot anyway...
entry 0x403ce000
ESP-ROM:esp32c3-api1-20210207
Build:Feb 7 2021
rst:0x3 (RTC_SW_SYS_RST),boot:0xc (SPI_FAST_FLASH_BOOT)
Saved PC:0x40383a6e
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fcd6100,len:0x438
load:0x403ce000,len:0x918
load:0x403d0000,len:0x24e4
SHA-256 comparison failed:
Calculated: 080c5cb68a075ced55f248b97bca965e3e5bd5da80a64e34e6a1638f89d6f64e
Expected: ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff
Attempting to boot anyway...
entry 0x403ce000
- cicciocb
- Site Admin
- Posts: 2060
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1358 times
- Contact:
Re: New AnnexToolKit 1.1 including release 1.48.22
I found the cause and how fix it.
The flash use the DIO mode and not the QIO mode as is usually done on the ESP32 series chip.
I discovered this behavior and then, on the luatos site I found this information that confirms
IO12 (GPIO12) and IO13 (GPIO13) are multiplexed for SPI signals SPIHD and SPIWP in QIO mode. In order to increase the number of available GPIOs, the development board chooses the DIO mode of 2-wire SPI. IO12 and IO13 are not connected to flash. Use your own compilation When installing the software, you need to pay attention to configure the flash as DIO mode.
Unfortunately simply changing the flash mode in the toolkit do not work (strange, by the way ) so I've been obliged to recompile the firmware
I found also this interesting page https://wiki.luatos.com/_static/bom/esp32c3.html
You can try with this .bin and it should work for your module.
However the OTA will not work as it requires a new release of the OTA firmware too
The flash use the DIO mode and not the QIO mode as is usually done on the ESP32 series chip.
I discovered this behavior and then, on the luatos site I found this information that confirms
IO12 (GPIO12) and IO13 (GPIO13) are multiplexed for SPI signals SPIHD and SPIWP in QIO mode. In order to increase the number of available GPIOs, the development board chooses the DIO mode of 2-wire SPI. IO12 and IO13 are not connected to flash. Use your own compilation When installing the software, you need to pay attention to configure the flash as DIO mode.
Unfortunately simply changing the flash mode in the toolkit do not work (strange, by the way ) so I've been obliged to recompile the firmware
I found also this interesting page https://wiki.luatos.com/_static/bom/esp32c3.html
You can try with this .bin and it should work for your module.
However the OTA will not work as it requires a new release of the OTA firmware too
You do not have the required permissions to view the files attached to this post.
Re: New AnnexToolKit 1.1 including release 1.48.22
Thanks a lot!!! I will test the new firmware tomorrow.
Re: New AnnexToolKit 1.1 including release 1.48.22
Work fine on my ESP32C3 board (Annex32-C3 BLE CAN 1.48.3), thanks![Local Link Removed for Guests] wrote: [Local Link Removed for Guests]Tue Dec 06, 2022 9:05 pm I found the cause and how fix it.
The flash use the DIO mode and not the QIO mode as is usually done on the ESP32 series chip.
I discovered this behavior and then, on the luatos site I found this information that confirms
IO12 (GPIO12) and IO13 (GPIO13) are multiplexed for SPI signals SPIHD and SPIWP in QIO mode. In order to increase the number of available GPIOs, the development board chooses the DIO mode of 2-wire SPI. IO12 and IO13 are not connected to flash. Use your own compilation When installing the software, you need to pay attention to configure the flash as DIO mode.
Unfortunately simply changing the flash mode in the toolkit do not work (strange, by the way ) so I've been obliged to recompile the firmware
I found also this interesting page https://wiki.luatos.com/_static/bom/esp32c3.html
You can try with this .bin Annex32C3.bin and it should work for your module.
However the OTA will not work as it requires a new release of the OTA firmware too
Re: New AnnexToolKit 1.1 including release 1.48.22
Finally got around to trying this again.
Still having the same issue, and it just reboots after a few seconds......
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0x1 (POWERON),boot:0x8 (SPI_FAST_FLASH_BOOT)
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce3808,len:0x39c
load:0x403c9700,len:0x9bc
load:0x403cc700,len:0x28dc
SHA-256 comparison failed:
Calculated: 5830b36eadda2ccdc73ac0028cd665f9a0ae0dcfc1ccf372c71f9cc6bad2ccc4
Expected: ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff
Attempting to boot anyway...
entry 0x403c98c0
Still having the same issue, and it just reboots after a few seconds......
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0x1 (POWERON),boot:0x8 (SPI_FAST_FLASH_BOOT)
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce3808,len:0x39c
load:0x403c9700,len:0x9bc
load:0x403cc700,len:0x28dc
SHA-256 comparison failed:
Calculated: 5830b36eadda2ccdc73ac0028cd665f9a0ae0dcfc1ccf372c71f9cc6bad2ccc4
Expected: ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff
Attempting to boot anyway...
entry 0x403c98c0
- cicciocb
- Site Admin
- Posts: 2060
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1358 times
- Contact:
Re: New AnnexToolKit 1.1 including release 1.48.22
Probably the module that you have is not compatible with the actual -S3 firmware.[Local Link Removed for Guests] wrote: [Local Link Removed for Guests]Tue Dec 20, 2022 7:25 pm Finally got around to trying this again.
Still having the same issue, and it just reboots after a few seconds......
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0x1 (POWERON),boot:0x8 (SPI_FAST_FLASH_BOOT)
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce3808,len:0x39c
load:0x403c9700,len:0x9bc
load:0x403cc700,len:0x28dc
SHA-256 comparison failed:
Calculated: 5830b36eadda2ccdc73ac0028cd665f9a0ae0dcfc1ccf372c71f9cc6bad2ccc4
Expected: ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff
Attempting to boot anyway...
entry 0x403c98c0
The actual firmware is based on PSRAM with octal PSRAM, maybe this is not the case for your module.
This seems very similar to what happened on the esp32-c3 module.
What is exactly your module? Do you have a schematic ?
edit
I think that you have one of these modules, the N8R2 exectly:
https://docs.espressif.com/projects/esp ... itc-1.html
This could explain as the module use a PSRAM with Quad and not octal SPI
Re: New AnnexToolKit 1.1 including release 1.48.22
Yes, that is the module I have, ESP32-S3-DEVKITC-1-N8R2[Local Link Removed for Guests] wrote: [Local Link Removed for Guests]Wed Dec 21, 2022 9:22 amProbably the module that you have is not compatible with the actual -S3 firmware.[Local Link Removed for Guests] wrote: [Local Link Removed for Guests]Tue Dec 20, 2022 7:25 pm Finally got around to trying this again.
Still having the same issue, and it just reboots after a few seconds......
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0x1 (POWERON),boot:0x8 (SPI_FAST_FLASH_BOOT)
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce3808,len:0x39c
load:0x403c9700,len:0x9bc
load:0x403cc700,len:0x28dc
SHA-256 comparison failed:
Calculated: 5830b36eadda2ccdc73ac0028cd665f9a0ae0dcfc1ccf372c71f9cc6bad2ccc4
Expected: ffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffffff
Attempting to boot anyway...
entry 0x403c98c0
The actual firmware is based on PSRAM with octal PSRAM, maybe this is not the case for your module.
This seems very similar to what happened on the esp32-c3 module.
What is exactly your module? Do you have a schematic ?
edit
I think that you have one of these modules, the N8R2 exectly:
https://docs.espressif.com/projects/esp ... itc-1.html
This could explain as the module use a PSRAM with Quad and not octal SPI
Re: New AnnexToolKit 1.1 including release 1.48.22
Hi, I think i have a similar issue, says it flashes ok, but get similar message in serial port.
My module is a Banana Pi BPI-Leaf-S3
cheers
My module is a Banana Pi BPI-Leaf-S3
cheers
- cicciocb
- Site Admin
- Posts: 2060
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1358 times
- Contact:
Re: New AnnexToolKit 1.1 including release 1.48.22
Could you test these versions for the esp32-s3?
This is with the PSRAM disabled and this is with a QIO psram enabled Please report .
This is with the PSRAM disabled and this is with a QIO psram enabled Please report .
You do not have the required permissions to view the files attached to this post.