Hallo Francesco,
Ich habe Heute den ESP32-2432S032C aus China erhalten
Nach dem ich den Annex32 CAN 1.51.8 LFS installiert habe und die Konfiguration Module ESP32-2432S eingestellt habe ist auf dem TFT nichts passiert, blieb schwarz.
Erst nach dem ich Module auf CUSTOM eingestellt habe
und die Advanced Settings wie unten:
eingestellt habe ist ein Bild auf dem TFT gekommen allerdings REVERS dargestellt
was ist da noch falsch ... ?
Hier die Anschlüsse für TFT und CAP_TOUCH
liebe Grüße
Waldemar
Modul ESP32-2432S032C_I
Modul ESP32-2432S032C_I
You do not have the required permissions to view the files attached to this post.
-
cicciocb
- Site Admin
- Posts: 2055
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1354 times
- Contact:
Re: Modul ESP32-2432S032C_I
Unfortunately this module is not supported, the one supported is the ESP32-2432S028 with resistive touchscreen.
You can select as you did, in advanced mode, the pinout for the TFT but the touchscreen will not work (only the resistive is supported for the ESP32).
You have a negative image because probably your TFT is an ILI9341 and not an ST7789 #5.
If the SDCARD shares the same pinout of the TFT, it should be possible to use it (check the schematics).
You can select as you did, in advanced mode, the pinout for the TFT but the touchscreen will not work (only the resistive is supported for the ESP32).
You have a negative image because probably your TFT is an ILI9341 and not an ST7789 #5.
If the SDCARD shares the same pinout of the TFT, it should be possible to use it (check the schematics).
Re: Modul ESP32-2432S032C_I
Hello cicciocb,
The capacitive touch since version Annex32 CAN 1.52.3 LFS works great.
Where I have a problem is the inverse display on the TFT.
And there is definitely an ST7789 installed.
The settings ST7789#0 to ST7789#4 show correct display
only with incorrect resolution and orientation.
Could you perhaps take a look at why the ST7789#5
displays the content inversely?
Kind regards,
Waldemar
The capacitive touch since version Annex32 CAN 1.52.3 LFS works great.
Where I have a problem is the inverse display on the TFT.
And there is definitely an ST7789 installed.
The settings ST7789#0 to ST7789#4 show correct display
only with incorrect resolution and orientation.
Could you perhaps take a look at why the ST7789#5
displays the content inversely?
Kind regards,
Waldemar
-
cicciocb
- Site Admin
- Posts: 2055
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1354 times
- Contact:
Re: Modul ESP32-2432S032C_I
Hello Cicciocb,
I tried with ILI9341 see picture
The ST7789#2 comes closest to the correct result apart from the edges on both sides.
and shows the content in correct colors.
I tried with ILI9341 see picture
The ST7789#2 comes closest to the correct result apart from the edges on both sides.
and shows the content in correct colors.
You do not have the required permissions to view the files attached to this post.
-
cicciocb
- Site Admin
- Posts: 2055
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1354 times
- Contact:
-
cicciocb
- Site Admin
- Posts: 2055
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1354 times
- Contact:
Re: Modul ESP32-2432S032C_I
Here's the ST7789#5
Here is the M5Stack#1
Here is the M5Stack#2
both m5Stack are mirror images
Here is the M5Stack#1
Here is the M5Stack#2
both m5Stack are mirror images
You do not have the required permissions to view the files attached to this post.
-
cicciocb
- Site Admin
- Posts: 2055
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1354 times
- Contact:
-
cicciocb
- Site Admin
- Posts: 2055
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 439 times
- Been thanked: 1354 times
- Contact:
Re: Modul ESP32-2432S032C_I
I just updated the version 1.52.3 with another ST7789 #6.
Try it and let me know.
Try it and let me know.