I just uploaded the ESPCAM 1.51.1.
You can use the OTA or the online flasher to update.
I did not tested so, let me know.
Base64 encoder
- cicciocb
- Site Admin
- Posts: 2095
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 450 times
- Been thanked: 1385 times
- Contact:
-
- Posts: 36
- Joined: Sat Feb 20, 2021 9:36 am
- Location: Sindelfingen, Germany
- Has thanked: 143 times
- Been thanked: 10 times
Re: Base64 encoder
I tried to test this morning, but honestly, perhaps I made a mistake when flashing a module where a Ver 1.49.2 CAM was running stable before:
Connected the module to the WEB Installer (this was the mistake) and flashed 1.51.1 ESP32 to the module. Annex worked so far. When I noticed the error, I flashed 1.51.1 CAM via OTA, which also worked. But since then the camera couldn´t be adressed in any way. Finally I erased the flash via the Toolkit and flashed 1.49.2 CAM and later 1.48.22 CAM also via the toolkit, the result is in all cases the same:
When adressing the camera eg
This ended with reboot:
I feel for the next tests, I have to buy a new module.
Any other idea would be appreciated very much.
Rainer
Connected the module to the WEB Installer (this was the mistake) and flashed 1.51.1 ESP32 to the module. Annex worked so far. When I noticed the error, I flashed 1.51.1 CAM via OTA, which also worked. But since then the camera couldn´t be adressed in any way. Finally I erased the flash via the Toolkit and flashed 1.49.2 CAM and later 1.48.22 CAM also via the toolkit, the result is in all cases the same:
When adressing the camera eg
Code: [Local Link Removed for Guests]
'
'Ver 1.48.22
wlog "init"
Ret = CAMERA.PARAMS("framesize",13)
wlog Ret
wait
Code: [Local Link Removed for Guests]
Number of program lines :6
Basic File Loaded: /test.bas
Program RunningProgram Running
Guru Meditation Error: Core 1 panic'ed (LoadProhibited). Exception was unhandled.
Core 1 register dump:
PC : 0x400e57e8 PS : 0x00060830 A0 : 0x800e4ad7 A1 : 0x3ffcdd60
A2 : 0x00000000 A3 : 0x3ffd6ac4 A4 : 0x3ffc5cac A5 : 0x3f41b508
A6 : 0x3ffcddbc A7 : 0x0000000d A8 : 0x800e57e4 A9 : 0x3ffcdd40
A10 : 0x00000001 A11 : 0x0000000d A12 : 0x3ffd635c A13 : 0x3ffc3df4
A14 : 0x00000008 A15 : 0x7ffa0000 SAR : 0x00000014 EXCCAUSE: 0x0000001c
EXCVADDR: 0x00000040 LBEG : 0x4008ca6d LEND : 0x4008ca91 LCOUNT : 0x8011870a
Backtrace: 0x400e57e5:0x3ffcdd60 0x400e4ad4:0x3ffcddf0 0x400e4c13:0x3ffcde30 0x400e4e78:0x3ffcde60 0x400e7cce:0x3ffcde90 0x4008210e:0x3ffcdec0 0x400f063f:0x3ffcdef0 0x400f088c:0x3ffcdf50 0x40117855:0x3ffcdf90
ELF file SHA256: 0000000000000000
Rebooting...
ets Jun 8 2016 00:22:57
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1344
load:0x40078000,len:13864
load:0x40080400,len:3608
entry 0x400805f0
Annex initializing...
PSRAM enabled
module Type 0 Display 255 SD_Card 0
OK
No SD cards found. Reverts to FFAT
AnnexCAM 1.48.22
(C) ciccioCB 2022
Personal use only, commercial use strictly prohibited
Chip revision 1 Freq 240
STARTING
Connecting to abc
.............
Connected to abc
IP address: 192.168.0.59
ws[/ws][1][2] connect
Any other idea would be appreciated very much.
Rainer
- cicciocb
- Site Admin
- Posts: 2095
- Joined: Mon Feb 03, 2020 1:15 pm
- Location: Toulouse
- Has thanked: 450 times
- Been thanked: 1385 times
- Contact:
Re: Base64 encoder
I tested personally yesterday night and it was working.
I think that you didn't selected the right module in the config page so the camera is not initialized.
This message is not correct
The module type should be 201 (for the esp32-cam or 202 for the M5 camera)
I think that you didn't selected the right module in the config page so the camera is not initialized.
This message is not correct
Code: [Local Link Removed for Guests]
module Type 0 Display 255 SD_Card 0
-
- Posts: 36
- Joined: Sat Feb 20, 2021 9:36 am
- Location: Sindelfingen, Germany
- Has thanked: 143 times
- Been thanked: 10 times
Re: Base64 encoder
Ooh, you are right ! I was too fast and forgot to set the module type on then config page.
Meanwhile I flashed another 2 "garden" CAMs and I can confirm everything is working as expected.
I thint the picture buffer works as in 1.48.22, but taking 4 additional pictures doesn´t matter.
Thank you for the hint !
Rainer
Meanwhile I flashed another 2 "garden" CAMs and I can confirm everything is working as expected.
I thint the picture buffer works as in 1.48.22, but taking 4 additional pictures doesn´t matter.
Thank you for the hint !
Rainer