ESP32 reboots every seconds with 1.43 CAN BLE
Posted: Thu Sep 09, 2021 6:46 pm
Hello,
I tried my program used for solar thermie because of its bigger memory on an ESP32, flashed it with the actual annex bin and put my program as well as the associated files on it.
Then the program worked for a minute or so and after that it began to boot always.
In the serial monitor I found the following message:
Guru Meditation Error: Core 1 panic'ed (IllegalInstruction). Exception was unhandled.
Core 1 register dump:
PC : 0x63615e01 PS : 0x00060430 A0 : 0x800ea711 A1 : 0x3ffcee20
A2 : 0x3ffcef5c A3 : 0x63615e01 A4 : 0x3ffc6008 A5 : 0xf4b332d3
A6 : 0x3ffcef60 A7 : 0x3ffcefcc A8 : 0x801058b0 A9 : 0x3ffcee00
A10 : 0x3ffe384c A11 : 0x3ffcee74 A12 : 0x000000ff A13 : 0x0000ff00
A14 : 0x00ff0000 A15 : 0xff000000 SAR : 0x0000000a EXCCAUSE: 0x00000000
EXCVADDR: 0x00000000 LBEG : 0x400013f9 LEND : 0x4000140d LCOUNT : 0xfffffffe
Backtrace: 0x63615e01:0x3ffcee20 0x400ea70e:0x3ffcee40 0x400e1a9f:0x3ffcf040 0x400e63b8:0x3ffcf060 0x400e66bf:0x3ffcf090 0x400e689c:0x3ffcf0c0 0x400e8786:0x3ffcf0f0 0x400f5d62:0x3ffcf120 0x400f650b:0x3ffcf180 0x400f66f1:0x3ffcf200 0x401486dd:0x3ffcf240 0x40091e31:0x3ffcf260
The Annex toolkit shows the following device informations:
Detecting chip type... ESP32
Chip is ESP32D0WDQ6 (revision 1)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
MAC: 98:f467:d6:b8
Uploading stub...
Running stub...
Stub running...
16 (100 %)
16 (100 %)
Has anybody an idea, what to do?
Thank you
Frank Martens
I tried my program used for solar thermie because of its bigger memory on an ESP32, flashed it with the actual annex bin and put my program as well as the associated files on it.
Then the program worked for a minute or so and after that it began to boot always.
In the serial monitor I found the following message:
Guru Meditation Error: Core 1 panic'ed (IllegalInstruction). Exception was unhandled.
Core 1 register dump:
PC : 0x63615e01 PS : 0x00060430 A0 : 0x800ea711 A1 : 0x3ffcee20
A2 : 0x3ffcef5c A3 : 0x63615e01 A4 : 0x3ffc6008 A5 : 0xf4b332d3
A6 : 0x3ffcef60 A7 : 0x3ffcefcc A8 : 0x801058b0 A9 : 0x3ffcee00
A10 : 0x3ffe384c A11 : 0x3ffcee74 A12 : 0x000000ff A13 : 0x0000ff00
A14 : 0x00ff0000 A15 : 0xff000000 SAR : 0x0000000a EXCCAUSE: 0x00000000
EXCVADDR: 0x00000000 LBEG : 0x400013f9 LEND : 0x4000140d LCOUNT : 0xfffffffe
Backtrace: 0x63615e01:0x3ffcee20 0x400ea70e:0x3ffcee40 0x400e1a9f:0x3ffcf040 0x400e63b8:0x3ffcf060 0x400e66bf:0x3ffcf090 0x400e689c:0x3ffcf0c0 0x400e8786:0x3ffcf0f0 0x400f5d62:0x3ffcf120 0x400f650b:0x3ffcf180 0x400f66f1:0x3ffcf200 0x401486dd:0x3ffcf240 0x40091e31:0x3ffcf260
The Annex toolkit shows the following device informations:
Detecting chip type... ESP32
Chip is ESP32D0WDQ6 (revision 1)
Features: WiFi, BT, Dual Core, 240MHz, VRef calibration in efuse, Coding Scheme None
MAC: 98:f467:d6:b8
Uploading stub...
Running stub...
Stub running...
16 (100 %)
16 (100 %)
Has anybody an idea, what to do?
Thank you
Frank Martens